How to Wire RGB LED Power Pods on Your UTV

By BOSS Audio Systems | Life at Full Volume | Published: 2026-10-20

Category: How-to Guides

Learn to wire BOSS Audio Power Pods with RGB LEDs on your UTV. Step-by-step guide for B40RGB and B62RGB, including mounting, power, and RF remote setup.

Quick answer

To wire RGB LED Power Pods on your UTV, mount the pods using the clamp system, connect the amplifier and LED power wires to your UTV's battery with the included low-voltage auto shut-off, and pair the wireless RF remote for lighting control.

Understand your Power Pod system

The BOSS Audio B40RGB and B62RGB Power Pods are all-in-one weatherproof sound systems with built-in Class-D amplifiers and RGB LED lighting. They are designed for UTVs, ATVs, and other off-road vehicles, with an IPX5 rating to handle dust and moisture. The wireless RF remote controls both audio and lighting, so wiring is straightforward: you only need to supply 12V DC power and mount the pods securely.

Choose the right location and mounting hardware

The B40RGB uses a clamp system for 1.5" to 2" O.D. tubing, while the B62RGB has a swivel metal clamp for 1.5" to 3" O.D. tubing. This makes them ideal for roll cages, grab bars, or roof racks. Ensure the mounting surface is clean and the clamp is tight enough to prevent vibration, but do not overtighten as it could damage the pod housing. The swivel feature on the B62RGB lets you aim the speakers for better sound projection.

Step-by-step wiring guide

Step 1: Mount the Power Pods: Attach each pod to a secure roll bar or tube using the provided clamp. For B40RGB, use the fixed clamp (1.5"–2" O.D.). For B62RGB, use the swivel clamp (1.5"–3" O.D.) and adjust the angle before tightening. Common mistake: mounting on a loose or thin tube that vibrates, causing rattling or pod damage. Check that the clamp fully engages the tube and the pod cannot rotate after tightening.
Step 2: Run the power and audio wires: Each pod has a single wiring harness that combines power, audio input, and LED control. Route the harness from the pod to your UTV's battery area, keeping it away from moving parts and exhaust heat. Use zip ties to secure the cable along the frame. Common mistake: leaving slack that can snag on brush or trail debris. Leave a small service loop near the pod for angle adjustments, but secure the rest tightly.
Step 3: Connect to the battery: Connect the red wire to the positive terminal and the black wire to the negative terminal of your UTV's 12V battery. The system includes a low-voltage auto shut-off to prevent battery drain when the vehicle is off. Common mistake: connecting directly to the UTV's accessory plug, which may not supply enough current or trigger the auto shut-off incorrectly. Always connect directly to the battery terminals for reliable power and protection.
Step 4: Pair the wireless RF remote: Turn on the UTV battery power. The RF remote should sync automatically within a few seconds. Test the audio and RGB lighting by pressing the mode buttons. If the lights do not respond, check that the remote has a fresh battery (CR2032) and is within 30 feet of the pods. Common mistake: assuming the remote is defective when it just needs a new battery or line-of-sight. Keep the remote battery compartment clean and replace the battery yearly.
Step 5: Test and secure all connections: Play audio from your smartphone or MP3 player through the 3.5mm auxiliary input. Cycle through the RGB lighting patterns using the remote. Confirm that the auto shut-off activates when the vehicle's battery voltage drops below the threshold (typically around 11.5V). Common mistake: skipping the voltage test and later finding a dead battery on the trail. Run the system for 10 minutes with the engine off to verify the shut-off works.

Product facts

B40RGB: IPX5-Rated (Weatherproof/Dustproof) and includes Auto Shut Off: Vehicle Low Battery Detection You can mount these pods outside the cabin without worry, and the auto shut-off protects your UTV battery from draining when the vehicle is off.
B40RGB
B62RGB: 6.5" High Power Speakers + 1" Dome Tweeters and Swivel Metal Clamp System 1.5" – 3" O.D. The larger drivers deliver fuller sound, and the adjustable clamp lets you angle the pod for optimal audio coverage in a side-by-side or open vehicle.
B62RGB