What You Get with the MRWT40RGB
The BOSS Audio MRWT40RGB is a 2-way waketower speaker system designed for marine use. It pairs a 4" (102 mm) poly injection midbass driver with a 1" (25 mm) dome tweeter, delivering clear full-range sound. The rubber surround helps protect the cone from moisture and UV exposure, while the IPX5 rating means the speakers are weatherproof and dustproof—important for any boat installation.
Beyond audio, the MRWT40RGB features 20 multicolor illumination options with multiple lighting patterns. A wireless remote control lets you change colors and patterns without leaving the helm. This guide covers the physical mounting, wiring, and RGB setup based on the supplied product specs.
MRWT40RGB Specs That Affect Installation
- MRWT40RGB: 2-Way System with 1" (25 mm) Dome Tweeter and 4" (102 mm) Midbass Driver The separate tweeter and midbass mean you need to route two sets of speaker wires per pod, or use the supplied crossover if included (not confirmed in catalog). Plan for clean wire runs inside the tower.

MRWT40RGB - MRWT40RGB: IPX5-Rated (Weatherproof/Dustproof) IPX5 means the speakers can handle low-pressure water jets and dust, making them suitable for exposed tower mounting. However, the rating does not confirm submersion protection—keep wiring connections sealed with marine-grade heat shrink or dielectric grease.
- MRWT40RGB: 20 Multicolor Illumination Options with Multi Pattern Options RGB requires a constant power source and a ground, separate from the audio signal. Plan a dedicated power wire from your boat's fuse panel to the tower for consistent lighting performance.
- MRWT40RGB: Wireless Remote Control The remote lets you change colors/patterns from anywhere on the boat, but it needs to be paired with the speakers' receiver. Keep the remote within range (follow the supplied product instructions for range) and replace the battery as needed.
Mounting the MRWT40RGB on Your Waketower
Before drilling, confirm the tower tube diameter and wall thickness. The MRWT40RGB uses a clamp-style mount (not confirmed in catalog, but typical for this product category). If your tower has non-standard tubing, you may need adapter brackets.
Use stainless steel hardware to prevent corrosion. Apply a marine-grade sealant around any drilled holes to maintain the IPX5 integrity.
- 1. Position the speaker pods: Hold each pod against the tower tube at your desired height and angle. Aim the tweeter toward the listening area for best high-frequency dispersion. Mark the clamp bolt locations with a pencil.
- 2. Attach the mounting clamps: Secure the clamps around the tower tube using the supplied bolts. Tighten evenly—do not overtighten, as this can crack the pod housing or deform the tube. Use a torque wrench if you know the tube's spec.
- 3. Run the speaker wire: Route the positive and negative wires from each pod down through the tower interior (if hollow) or along the outside using adhesive wire clips. Keep audio wires away from the RGB power wire to avoid noise induction.
- 4. Connect the audio signal: Wire the speaker terminals to your marine amplifier or head unit. Polarity matters: connect positive to positive, negative to negative. Use crimp connectors or solder + heat shrink for reliable connections.
Wiring the RGB Lighting
The MRWT40RGB's illumination requires a DC power source. Run a fused positive wire from your boat's battery or distribution panel to the tower, and a negative wire to a common ground bus. Use marine-grade tinned wire (14-16 AWG recommended for short runs) to resist corrosion.
The wireless remote receiver module (if separate) should be mounted in a dry location, such as under the helm dash. Pair the remote per the supplied instructions—typically by pressing a sync button on the receiver and then a button on the remote. If the remote does not respond, replace the coin cell battery (CR2032 or similar, not confirmed).
What the Catalog Does Not Confirm
The supplied product record does not include detailed installation instructions, such as specific torque values, wire gauge recommendations, or the exact pairing procedure for the remote. For these details, refer to the manual that ships with the MRWT40RGB or contact BOSS Audio support. The speakers are designed for marine use, but the catalog does not confirm included mounting hardware or bracket dimensions—verify before drilling.
Always test the speakers and RGB functions before finalizing the mounting. Power up the system and cycle through the illumination options using the remote to ensure all 20 colors and patterns work correctly. If the remote does not change colors, check the receiver's power and the remote's battery.

